1. Semi-automatic and manual punching machines must be equipped with two-hand brake switches, and it is strictly forbidden to press with pedal or one-hand start switch.
2. After the high-speed punching machine is finished, and after normal stamping, close the soundproof box (except for the 8065 side inspection side packaging of the product).
3. During continuous punching, employees cannot take the product with their hands within 1M of the punching machine.
4. When the technician is on the mold and adjust the machine, only one person can debug, not two people.
5. The technician can adjust the machine and feed the material, only outside the machine, and the distance is not less than 1M.
6. Be sure to tighten the screws when setting up the mold, and stop the machine for 4 hours to check if the screws are loose.
7. When there is a problem in the production process of the mold, it is not necessary to remove the mold. When the mold is directly repaired on the machine tool, the power supply of the injection molding machine must be turned off and the repairing sign can be hung on the power box before the mold repair can be implemented.
8. All tools are returned to the tool box after use, and can not be placed on the machine table to prevent the tools from slipping and hurting people.
9. When the machine is not in production, cut off the power supply in time.
10. For short and small workpieces, special tools should be used instead of feeding or picking up the parts directly by hand.
11. The producer should stand properly, keep a certain distance between his hands and head and the punch, and always pay attention to the punch, and it is strictly forbidden to chat with others.
12. Operators and mold repairers are strictly prohibited from reaching into the mold during production.
13. When installing the suction fan, the operator is strictly forbidden to reach out to the motor to clean up waste.
14. It is strictly forbidden to wear slippers when going to work, so as not to hit your feet with molds and iron blocks in the workshop. Monitors, fitters, and mold repairers must wear protective shoes when going to work;
15. It is strictly forbidden for male operators to wear long hair, and for female operators, long hair should be coiled up to prevent long hair from getting caught in the flywheel.
16. Pay attention to fire prevention for other oils such as white electric oil, alcohol, cleaning agent and so on.
17. When packing materials, scraps and molds, please wear gloves to avoid scratching your hands.
18. When there is oil, it must be cleaned up in time to avoid slipping and falling.
19. It is strictly forbidden to wear gloves when drilling and milling machines; when using the grinder, wear a mask and eye protection to protect yourself.
20. Pay attention to drag the mold to prevent it from falling on the ground (you must put the flatbed cart to the lowest level to pull the mold).
21. It is strictly forbidden for non-electricians to connect to electricity and repair the machine.
22. It is strictly forbidden to blow the wind gun at people, which can easily hurt the eyes.
23. The operator needs to wear earplugs.
24. When the machine is found to be abnormal, turn off the power first and then find the technician on duty to deal with it in time. Do not deal with it without authorization.
25. When a new employee goes to work on the first day, the team leader must explain the safety operation rules to him, and learn the safety operation rules once a day in the first week.
26. When adjusting the machine, be sure to adjust the machine to single-acting, and it is strictly forbidden to hit the continuous discharge belt.
27. Do not store any flammable or explosive materials under the switch.
28. Operators are strictly prohibited from chasing, chasing and hitting in the workshop to avoid falling, knocking over the product or hurting themselves.
29. Carry out the equipment inspection according to the inspection content on the equipment check card, pay special attention to whether the guiding and braking devices of the punch press are operating normally, and the functions of single punching and continuous punching are distinct.
30. When installing the mold on a small punch (10T), first loosen the locking device of the guide rail, install the upper and lower molds, and then adjust the guide rail stroke until it meets the requirements and lock the fastening device. In addition, when the mold is mounted on the high punch, it must be After hitting the single stroke stroke, the upper mold is locked, and the lower mold is locked after hydraulic clamping. Check again before production. ·
31. Special tools (pliers, hooks) must be used when discharging or manually feeding and picking blanks individually, and it is strictly forbidden to send and pick blanks by hand. A single switch will hurt your hands, but a double switch. The machine must not leak oil, otherwise it will fall off. Do not expose the power source, which is dangerous.
32. Wear gloves and concentrate when punching iron sheets, otherwise your hands will be injured.
33. During work, first check whether there are any abnormalities in the operation of the equipment, such as unclear orders, continuous rushing, poor operation or electrical failures, immediately shut down the machine and ask the technician on duty to deal with it.
34. It is strictly forbidden to use the foot switch on the punch, and all the original equipment of the machine should be removed.
35. When cleaning and inspecting the equipment, the power supply must be cut off before the operation.
36. Cut off the power, clean and scrub the work surface, remove the mold for maintenance and storage, and check the lubrication system oil at a certain time every week.
